Duck house: building tweaks and trim

Three more days on the duck house project.

Firstly, I bought a much more compact cap for the end of the feeder tube. I want a removable cap, so I can clean out the tube every so often. You can see my original notion on the left, basically the same as I used in the chicken coop, but that clearly would take up too much of the length of the pipe in this situation. So I found a different kind, that adds pretty much no length to the pipe, attaching by expanding a rubber gasket inside the pipe. This will work much better:

Pipe cap

Another purchase was an automatic door opener, the same model I use in both chicken coops. It has a light sensor to open the door at dawn, and close it at dusk, so it needs to be outside. I cut a hole through the front (west) wall, and temporarily installed it (I’ll remove it again when painting):

Automatic opener

Here’s the inside view of the automatic opener and duck door. The opener is screwed from the back onto a couple of bits of wood, such that the string from it hangs inside; later it will be tied to the door. An unusual installation, but means I don’t need any pulleys like on the old coop:

Automatic opener

Next, I made the inner floor, a second floor layer that can be pulled out to aid cleaning out the duck house. It has thin runners on the bottom to reduce friction, and prevent any water from being trapped between the two layers:

Inner floor

Here’s the inner floor in place:

Inner floor

I recently mentioned temporarily using the duck house camera to watch the shop cat Pepper. I retrieved the camera and temporarily clamped it to the house, to determine the best mounting location:

Camera

Here’s the camera view from my preferred location, just inside the maintenance door. This gives a view into the nesting boxes and almost all of the floor space, except the corner under the camera, which is where the water dispenser will be located. (Enjoy the recursive photo of me capturing the view on my iPad):

Camera view

I also tried other camera positions, like the vent side:

Camera view

And behind the feeder tube:

Camera view

But I think the originally planned location by the maintenance door gives the best view.

Since there will be the camera, a heated water dispenser, and a light in the duck house, I drilled a hole near the roof into the storage cupboard for their wires:

Hole for wires

On to the trim work. I added trim around the internal treat door. You can also see the wire hole in the top-right, and below it a notched bit of plywood to cover the hole:

Treat door

I added trim to the edge of the roof. It’ll later have metal drip strip and shingles, like the cat house:

Roof edge trim

Awning trim; the board at the top of the awning isn’t attached yet, as it’ll go on after the shingles, to hide the nails of the top row:

Awning trim

Duck door trim:

Duck door trim

Opener trim:

Opener trim

The big vent on the south wall has a cover that slides vertically. It will be held at various heights by a slide bolt on either side that slides into holes drilled in the trim:

Holes for vent bolts

I glued bits of plywood to the vent cover, to later mount the bolts onto to get the right depth:

Vent cover

The vent cover installed. The notch out of the trim allows the cover to be slid to the left to be removed entirely (which I probably will never do, other than when painting):

Vent cover installed

All the roof, corner, and door surround trim are now installed. I still need to do the trim on the doors themselves, and the fake board-and-batten styling.

Let’s take spin around the duck house. Here the east and north sides (cupboard and maintenance doors):

Finished trim

The north and west sides (maintenance and duck doors):

Finished trim

The west and south sides (duck door and vent):

Finished trim

The south and east sides (vent and cupboard):

Finished trim

Finally, I did a bit of caulking of the joins:

Caulk

2 thoughts on “Duck house: building tweaks and trim

  1. Pingback: David Sinclair

Leave a Reply

Your email address will not be published. Required fields are marked *