I did some more work on the new cat house over the weekend, building the roof and some of the trim.

Firstly I made framing for the insulated ceiling of the shelter part:

And added three layers of the half-inch insulation foam. Heat rises, so I thought having thicker insulation in the ceiling made sense (and I bought more than I needed, so have plenty spare):

This ceiling was then attached to a half inch plywood panel, that will form the roof (the cutouts are for wires):

Here’s the roof installed, with some trim along the edge. Like the floor, the roof is not attached to the walls yet, so I can move the structure to the final destination in separate pieces; they will be screwed together there:

A view inside the shelter portion, with the ceiling in place:

I added a board above the top of the front wall, which will form the base of the front façade:

And started to add some trim on the corners etc. I also changed my mind on the maintenance door; as you know, the entire front of the shelter portion opens; I was going to have it swing open, hinged on the left, but decided that it’s too heavy for that to work well, so will make it slide to the left instead. It won’t be opened often (probably only a couple of times a year, to add or remove the heated beds, and close or open the vent covers), but I still want it to be fairly easy to open:

I added trim around the awnings; I bought metal drip strip for them, along with the roof, but I haven’t decided if I’ll actually use it on the awnings, since I worry about sharp edges close to the cats. I’ll decide that when I’m ready to do the roofing shingles. If I don’t, the trim will make the edge look nice; if I do, the trim will provide the right height backing for it:

More trim around the side door and corners; you can also see the underside of the roof overhang:

I’ve run out of 1×2 wood, and am ready for some other extra bits, so I’ll make a run to Home Depot later in the week. Next weekend I currently plan to do the roofing (drip strip, paper, and shingles). And perhaps more trim and/or the façades, if I have time.

I’ve decided to slow down work on the new cat house, as I need to spend more time on consulting and Dejal apps, and this isn’t urgent, since the cats already have a heated shelter and raccoon-proof feeder. But I am still keen to get this finished, and am enjoying working on it, so will do at least a few hours on it each weekend.

Yesterday I added wheels to the maintenance door; the whole front of the shelter portion of the structure. As mentioned in my previous post, I was originally going to have it swing open, but decided to make it slide instead, for weight reasons. So I got some little casters to make it slide more easily, and cut notches out of the bottom for them:

Here’s a closer view; you can also see the cat door temporarily in place (to check the fit):

I added a strip of plywood to hide the casters:

I also added a thin board to the back of the deck, to act as a track for the casters (and make the door the right height):

Here’s the door in place, opened:

And closed:

That’s basically it for this time. My next priority is a second beehive stand (for the two new hives we’ll be adding), and a rail for this door to slide on when open. Then probably the facades and trim. I mentioned last time that I was thinking about doing roofing next, but I think it’d be better to do that after the walls are painted. (I was going to do it before the facades due to the flashing at the back of them, but I realized I can build that as another separate piece, so can be lifted off for roofing.)

With my slower pace, I probably won’t finish this project until sometime in May, but that’s fine.

Over the weekend I got back to working on the new cat house, in between planting trees, bee inspections, and other stuff.

This time, I built the facades at the top of the front wall, to help give it an old-west theme.

As you may recall, the structure is divided into two sides: the shelter on the left, and the feeding station on the right. So the facades reflect this, suggesting two separate (but joined) buildings, with a squared two-step facade on the shelter side, and a triangle facade on the feeder side.

Here are the back and sides:

Some interior framing added to the top:

Behind the facades is a metal roof-to-wall flashing, that will sit on top of the roofing shingles. The wall side was roughly cut with a reciprocating saw:

The rough edge of the flashing is hidden behind another layer of plywood:

Top 8×1 boards:

Front view with the top boards in place:

Like other parts of the structure, the facades can be removed, to make installation easier. It’ll be screwed into place. Here, I’m adding more bracing:

Added some corner trim:

Back view, showing trim under the top boards:

The entire front of the facades is a door that will hinge downward, to provide access to the cavity within, which will house wires and power supplies for the cameras and heating pads.

Here I added trim to the door:

The center of each facade will contain a custom sign purchased via Etsy; more on those in the future.

The door clamped in place:

A view of the whole structure:

Another angle:

The basic structure is now mostly complete; all that remains before it can be painted is some decorative trim work. There’s still a fair bit to do: painting, roofing, door hardware, some decorative touches, and more.

Another weekend, another few hours on the cat shelter construction.

This was one of the last bits of primary building: adding decorative trim to the walls, to make them appear like board-and-batten siding.

But first, a rare photo of Pepper, one of the two feral cats that live in the workshop. Pepper lives high on a shelf in the front part, and Pansy lives in the back half:

As previously mentioned, I ordered some signs for the two parts of the structure. I actually got two custom signs from two different people, and decided on one pair that we preferred. Here’s the “Cat House Saloon” sign for the shelter, made by HarkenHomeWoodcraft on Etsy, temporarily resting in place:

And the “Mercantile” sign for the feeder:

A view of both signs:

Anyway, back to the trim work. I added 1×0.5″ boards (ripped from 1x2s) to the walls, glued and nailed in place, to simulate board-and-batten style siding:

On the front:

On the facade front:

The shelter maintenance door removed, to make it easier to add the trim on the bottom half:

The feeder side door & wall:

The front and side:

Another angle:

Peeking under the awnings; the boards laying on the deck are cut pieces for the window surrounds, so they can be painted before installing the windows:

Above the awnings:

Adding trim to the back of the facades:

And the back wall, which will probably not be visible, but still worth making look nice:

I shoved the roof forward to make it easier to do the back wall; like many other parts, the roof will remain removable until installation:

That’s basically it for the woodwork. Next up is caulking and painting.

Yesterday I linked to an excellent video that the Feral Cat Coalition of Oregon (FCCO) produced that featured our feral cats. So I thought I’d do a little update with some new photos of the cats.

They’re all still doing well, and are enjoying scampering around and laying in the sun on these warmer days. This morning was a bit damp, but of course they still turned up for breakfast from the auto-feeder, and took turns eating.

Here you can see Spud sitting on top of the feeder roof, one cat eating and another queued behind her, and Portabella in the foreground:

Can you see two cats in this picture?

Look closer: Poppy sitting amongst the flowers next to the lawn:

They’re still enjoying their heated shelter, even on warm days like yesterday:

Sometimes ya gotta stretch out:

And yawn!

I am continuing to work on a fancy new western-themed combo shelter and feeder for them. Check out the cat shelter blog posts for details of the building process.

Here are a couple of recent shots, showing the current state:

Want to see more of the cats, building the shelter, and more? Follow Yellow Cottage Homestead on Twitter, Facebook, Micro.blog, or via RSS.