Cat update for week ending March 30

About half as many photos this week.

A cute cat:

Cute cat

Scratching the wall carpeting. That’s fine, that’s one reason it’s there (also for more comfort & warmth). It is glued and screwed in place, so should be pretty resistant to their attentions:

Scratching cat

A possum & raccoon encounter on the deck (no cats home at the time):

Possum & raccoon encounter

A pile of three cats, when another arrives:

Four cats

Five cats inside:

Five cats

Five cats downstairs. I love how they lay on top of each other:

Five cats

A couple of cats waiting for more breakfast to be dispensed:

Cats waiting for more breakfast

Cat hugs:

Cats

The alien gray cat now has a collar with a bell; definitely owned by someone:

Alien gray cat

The twins arrive together for dinner:

Twins arrive

The twin cats:

Twin cats

Duck house: last of the battens

Last Saturday I finished off adding the battens for the fake board-and-batten siding.

Here’s the front (west) wall:

Battens

A closer view of that wall.  There’s a gap between the bottom of the battens and the loose board above the awning, as it will be attached after the roofing shingles, which will raise it up a bit:

Battens

The north wall, with new battens to the left of the maintenance doors:

Battens

The east wall, with the cupboard doors, and new battens below the doors:

Battens

The south wall, with the sliding vent.  The wall behind the vent cover is recessed enough to allow for the battens (almost like I planned it, eh):

Battens

I drilled a hole through the wall from the cupboard for power cords (power to the house, and from the house to the pond pump).  To make them tidier, I added a conduit with a removable cover for the wires to travel down the wall:

Power cord conduit

Here’s the inside of the power cord hole, and the cover for the inside, with a notch for the wires:

Power cord hole & cover

I also added a surround to screw the cover into:

Power cord hole surround

And a similar surround for the power cord hole between the cupboard and main part:

Power cord hole surround

Finally, I added a couple of boards to the back of the cupboard to enable adding screws to mount the power strip and light timer:

Mounts for electronics

That concludes the construction phase, at least until I build the floor joists and ramp. Next up: starting painting!

Wild ducks visiting pond, and more pond wading

This morning a pair of wild ducks visited our pond for a pitstop of about half an hour.

Wild ducks in pond

Wild ducks in pond

Wild ducks in pond

Wild ducks in pond

Wild ducks in pond

The pond pump fell (or was pushed) over again, so I added a wider pot to hopefully give it more stability:

David in pond

Me in the pond next to the pump:

David in pond

I waded a bit deeper to clean out more debris (and just for the fun of it); this is about two-thirds of the way back towards the deep end:

David in pond

Bee inspection & treatment; queen sighted

On Sunday we did an inspection and treatment of the beehives.

Here Jenn is pulling out a frame from the yellow beehive; notice the white rack that holds a frame, to make space to pull others out more easily:

Jenn inspecting beehive

We checked for mites via a sugar shake test, where powdered sugar is added to a jar of bees, shaken, water added, then mites counted:

Powdered suger on jar of bees

The bees are unharmed by this; they are returned to the hive, where others will clean them off (tasty sugar!):

Sugary bees

Adding an oxalic acid sugar water mix, that should kill mites without harming the bees:

Bee treatment

A frame with some honey on the left, and capped brood (baby bees) on the right:

Bee frame

Lots of honey (or sugar water from the feeder):

Bee frame

A couple of hive boxes; the bees had very little activity in the bottom box, so we swapped them; they tend to want to move upwards, so would continue to ignore the bottom box if left there:

Hive boxes

Some closeups of bees:

Closeup of bees

Closeup of bees

Closeup of bees

We spotted the queen in the Flow hive; I’ve circled her here:

Queen sighted

A classic beehive frame, with capped brood in the center:

Bee frame

A bunch of bees hanging out at the entrance:

Bees

The Flow beehive:

Beehive

The yellow beehive:

Beehive

Pond pump tweak

A quick pond update.

The pond pump fell (or was pushed) over again, so again I waded into the pond to right it. This time, I moved it from the lightweight plastic pot it was in into a heavier ceramic one, with some rocks for extra weight:

Pond pump

Here it is in position:

Pond pump

I waded deeper in the pond to clear out some floating debris. It’s hard to tell from the camera, but I’m only about halfway back; it gets much deeper in the back half:

David in pond

We saw the smaller fish this week; great to see lots of little ones. Only a few visible in this picture, but there are many more. They’re about two years old:

Fish

The heron visited again early this morning, and wandered around for about two hours, but didn’t seem to catch anything this time (the streaks in this picture are motion-blurred raindrops):

Heron

Cat update for week ending March 23

There have been regular visits by raccoons and possums, but nothing too dramatic, so I’m not including any pictures of them this time.

Four cats inside the shelter:

Four cats inside shelter

A queue waiting for more breakfast to be dispensed:

Waiting for breakfast

A brave/stupid jay in the cat feeder:

Bird in cat feeder

Three cats:

Three cats

The front shop cat, Pepper, sitting by the duck house:

Shop cat

Two cats in the shelter:

Two cats

Very relaxed cats:

Two cats

Another joins them:

Three cats

A very Poppy face at the water dish, with Porcini relaxing on the ground:

Three cats

Poppy is the mother of the kittens, but she can still be kitten-like at times:

Psycho cat

Too close!

Up close

Cat snuggles:

Cat snuggles

Two cats climbing the tree next to the cat house.  I removed the heated water dish, now that it’s getting warmer; we probably won’t be below freezing again:

Climbing tree

A sequence of three images of jumping down from the roof:

Jumping down

Jumping down

Jumping down

Poppy greets her kids:

Three cats

I saw a new alien cat when reviewing the footage this morning; I don’t think I’ve seen this one before:

New alien cat

Finally, Spud came and stared at me in the office, from the front steps:

Cat on steps

Heron, raccoon, and me in the pond

Some pictures from the big pond.

I recently added a camera that has a view of the pond, in anticipation of having ducks there. It has been interesting to see some of the wildlife that visits the pond.

Apparently raccoons can swim:

Swimming raccoon

We were pretty sure that herons visited the pond, but hadn’t seen one till a couple of days ago, when it was captured via the camera. Here’s a heron landing:

Heron landing

And strolling around in the shallow part of the pond:

Heron in pond

The heron visited again that night; I didn’t realize they were nocturnal hunters too. Here it has a frog, which it ate (sorry about the spiderweb in front of the camera):

Heron with frog

Yesterday I waded into the pond and righted the fountain pump, which had fallen (or was pushed) over, and switched it on:

David in pond

The fountain helps aerate the water. We also have a waterfall and stream, but that tends to make the pond level drop, so we usually don’t have it active.

Here’s the fountain pump:

Pond pump

I noticed one of the water lily baskets on its side, so righted that too, and found several sacs of salamander eggs on it. Interesting how the stalks were trying to compensate for being on its side, too:

Salamander eggs

Here’s a salamander:

Salamander

The pond level was low, so I also turned on the water to the pond taps, and turned on the tap to top up the pond:

Filling pond

Beehive temperature sensors

Yesterday we did our first inspection of the year of our two beehives. We weren’t sure about one of the hives, but both survived the winter. Now that the weather is getting warmer, and flowers are starting to bloom, the bees are active again, replenishing their stores, and the queens are busy laying brood to ramp up the populations.

While we were at it, we took the opportunity to install a couple of BroodMinder temperature sensors in each hive. These record the internal temperature, which can indicate the health and state of the hive. The sensors sync via Bluetooth to an app on Jenn’s iPhone.

Installing BroodMinder temperature sensor

Here’s the yellow hive with two sensor tags sticking out:

Beehive

Jenn doing a quick inspection of the Flow hive:

Jenn inspecting hive

A beehive frame, showing some stored honey on the right, some capped brood in the middle, and good activity:

Beehive frame

Some bees around the entrance, including some with full pollen baskets:

Bees

Duck house: building doors

Some more progress on the duck house project.

I bought a special water dispenser for the ducks (when they’re grown). Ducks have slightly different needs than chickens, in that they need to dip their large bills in water to drink and eat. This waterer has three removable cups for drinking (though one will be unreachable in the corner), a reservoir, and a built-in thermostatically-controlled heater, so the water doesn’t freeze in winter:

Duck waterer & camera

Since the waterer was a bit bigger than expected, I also raised the camera up a bit. Here’s the view from the camera:

View from camera

I tried a bag of feed in the cupboard, to see how well it’d fit. Seems to work laying down or standing up, about as well as I expected. Storing a bag or two of food there will make it easier to refill the food jug:

Trying food in cupboard

On to the door trim:

Door trim

Here’s one of the cupboard doors, with 1×2 trim around the edges. The plywood sticks out a bit on the right edge (in the foreground in this orientation), so it covers the gap between the two doors. Which of course means the other (right-hand) door has to be opened first, which is by some strange coincidence the one I expect to open most:

Door trim

Both cupboard doors:

Cupboard doors

I paused for a picnic lunch in the back of the shop (yes, it was still very cold):

David

Adding trim to the maintenance doors:

Cupboard doors

I changed my mind about the design of the maintenance doors. Originally I was going to have a single large outer door, with a vertically split inner door. I decided that a single outer door would be too large, so considered doing double doors like the cupboard, but then realized I could combine the inner and outer doors into one set. So I made four-part doors, again with plywood covering the gaps between the doors:

Maintenance doors

The way it is configured, I can undo one bolt (to be added after painting) to open just the top-left door for a quick peek, or two bolts to open just the top-left and top-right doors to access the ducks without them able to escape (which I expect will be especially useful when they are ducklings), or one bolt to open just the left two doors together (they’ll be connected with a bolt), or the left two and the right two for full access. I think this will be very versatile.

Here’s just the top-left door open:

Maintenance doors

In addition to the bolts, the doors will be held closed with roller catches. The bottom doors will have theirs mounted under the floor, to be out of the way:

Roller catch

And the top doors will have their roller catches mounted above the doors:

Roller catch

Here’s me using an air finish nailer to attach the board for the top roller catches, captured from the duck camera:

Nailing

Next up was adding thin strips of wood to make the doors and walls appear like board-&-batten styling, like I did with the cat house. So the first step was to rip (cut lengthwise) some 1×2 boards into 1×0.5 batten strips:

Ripping boards

I started adding the battens on the cupboard doors:

Board & batten on doors

Then the maintenance doors:

Board & batten on doors

I also added an extra bit of plywood to the corner that will cover up the two small holes between the four doors:

Hole cover detail

Finally (for now), battens on the vent cover:

Board & batten on doors

Next up, I will add the batten strips on the walls, do some extra bracing for attaching electrical stuff, and more caulking. Then I’ll be ready to start painting!